Feel free to ask questions! I think the pictures do a good job explaining how I go about it though.
| Official Luthiers Forum! http://www-.luthiersforum.com/forum/ |
|
| Making Kirfed Lining http://www-.luthiersforum.com/forum/viewtopic.php?f=10117&t=46654 |
Page 1 of 1 |
| Author: | Nils [ Thu Nov 12, 2015 9:52 am ] |
| Post subject: | Making Kirfed Lining |
Feel free to ask questions! I think the pictures do a good job explaining how I go about it though.
|
|
| Author: | BradHall [ Thu Nov 12, 2015 10:58 am ] |
| Post subject: | Re: Making Kirfed Lining |
Nicely done. The clothespin hold down and feather board are pure genius. |
|
| Author: | kwerry [ Fri Nov 20, 2015 3:40 pm ] |
| Post subject: | Re: Making Kirfed Lining |
Yes well done, I'm sure I'll steal the clothes pin idea for some future jigs.. Kerry |
|
| Author: | Pmaj7 [ Mon Dec 21, 2015 11:41 pm ] |
| Post subject: | Re: Making Kirfed Lining |
Not quite catching how that works. Do you have a video? |
|
| Author: | Gary Gill [ Tue Dec 22, 2015 5:51 am ] |
| Post subject: | Re: Making Kirfed Lining |
Are you indexing on the previous saw cut? |
|
| Author: | MaxBishop [ Tue Dec 22, 2015 8:19 am ] |
| Post subject: | Re: Making Kirfed Lining |
Looks like some of us need a bit more elucidation of the operation. Looks like a cool set up, but still don't get the details of how it works. Thanks, Max |
|
| Author: | Nils [ Tue Dec 22, 2015 11:04 pm ] |
| Post subject: | Re: Making Kirfed Lining |
Step 1: get strips to proper width and height Step 2: bevel edge with router bit Step 3: slide under the tensioner with the toothpick glued to it, and continue to feed it through until its under the roller Step 4: make your first cut. Step 5: advance by whatever distance you want between kirfs. (you can see I just have a pencil mark to tell me where to stop. |
|
| Author: | sdsollod [ Wed Dec 23, 2015 10:06 am ] |
| Post subject: | Re: Making Kirfed Lining |
Here's my jig I threw together.... First, I use part of the jig to plane the strip into shape. Then, I turn it around and on the band saw, slide the sled to stop and then move the strip forward and register for the next cut on a thin piece of wood that keeps the distance between cuts equal. |
|
| Author: | sdsollod [ Thu Dec 24, 2015 10:41 pm ] |
| Post subject: | Re: Making Kirfed Lining |
Nils, Didn't mean to hijack your thread... Just sharing what I did. I guess there different ways to do it. |
|
| Author: | Nils [ Sat Dec 26, 2015 9:31 pm ] |
| Post subject: | Re: Making Kirfed Lining |
sdsollod wrote: Nils, Didn't mean to hijack your thread... Just sharing what I did. I guess there different ways to do it. No worries, sharing is what this is all about. ![[:Y:]](./images/smilies/smiley20.gif "Thumbs Up")
|
|
| Author: | rlrhett [ Sun Dec 27, 2015 12:52 am ] |
| Post subject: | Re: Making Kirfed Lining |
Steve do you pick up the strip and drop it down on the little sliver of wood for each cut? If not how do you use the little sliver to index? Sent from my iPhone using Tapatalk |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|